MixVibes VFX CONTROL Manuel d'utilisateur télécharger pdf (Page 39)

CMJ

vibe-watermark-bright.pdf 03/04/2009 16:07:52vibe-watermark-bright.pdf 03/04/2009 16:07:52

9 Preferences

•

All Relative: in this mode, the playback position of the control record/disc does not correspond with the playback

position of the audio ﬁle in the player. Use the All Relative mode when you want to use non-linear functions like hot

cues (Locations) and Loops. In this mode you can use the ’drop to location’ feature.

’Drop to location’: with vinyl, set the needle on a vinyl position (3s-1mn/1-2mn/2-3mn/3-4mn/4-5mn) allows to go to a

MIXVIBES VFX location. With CD, store locations on the CD deck at positions ~50ms/100ms/150ms and go to these locations

allow to go to a MIXVIBES VFX location.

Audio interface: selects your audio interface.

Audio input: chooses the signal source among the inputs.

Timecode Quality

: displays the percentage of good time code and the volume value. The percentage must be 90% or

higher. If the percentage is not satisfactory, clean up your needles or visit our support webpage.

Adjust Gain

: sets the gain dB value of the input signal. This value could be immediately controlled through the view meter:

the view meter should reach the red level.

Phono Input

: this is a software emulation of RIAA preamp. This allows you to plug your PHONO turntables directly in your

soundcard. If your turntables have LINE signal, there is no need to use this preamp.

45RPM: checks this option if the turntable works in 45RPM speed.

Left/Right Inverse: allows a left/right inversion of your turntable/CD player wires.

Phase Inverse: allows a phase inversion. Some needles create a phase inversion (MIXVIBES VFX automatically detects it).

Offset

: creates a lead-in on your vinyl. Deﬁne this lead either in millisecond (1000ms= 1 second) and press ’Apply’ or put the

needle where you want on your vinyl, press ’Save’ then ’Apply’. You can also right click on CUE button on the mixer channel.

Visual control

of the signal that is going through your turntable. You may detect on this screen mass problems, electric

interference or even rumbles.

Noise level: sets the noise level in dB.

Noise ﬁlter: sets the anti noise ﬁlter frequency.

These 2 options are really important. If there are rumble, Electrical problems, bad ground or others noises coming from the

turntable you would increase the noise ﬁlter (for ex 150) to cleanup the input signal. The more important the noise coming

from your turntable is, the more you should increase the frequency but the precision will decrease mainly at a low speed. If

when you stop the vinyl, MIXVIBES VFX continues to play, then you need to increase the noise Level: for ex. -35dB (default is

-40dB). For a better sensibility you can lower this value: for ex. -45 dB

Calibrate 1, 2, 3 or 4: launches the calibration of your ﬁrst, second, third, fourth turntable.

One active turntable

: activates/deactivates the one active turntable mode. Use this feature only if you are using only one

turntable.

Apply: applies a modiﬁcation. After each modiﬁcation, you must click on this button.

Advanced: gives access to special parameters of MIXVIBES VFX.

Circle: switches your calibration view from sinusoid to a circle. A clean time code is represented by a homogeneous circle.

CMY

vinyl_cd_input.pdf 06/11/2009 15:43:41

Vinyl/CD input

39 / 44

1 2 ... 34 35 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

MixVibes VFX CONTROL Manuel d'utilisateur Page 39

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel d'édition audio MixVibes VFX CONTROL